Account Policy

Account Policy defines the security requirements that accounts must meet and influences users sessions.

Policy is defined on groups so that membership of a group influences the security of its members. This allows you to express that if you can access a system or resource, then the account must also meet the policy requirements.

All account policy settings may be managed by members of idm_account_policy_admins. This is assigned to idm_admin by default.

Default Account Policy

A default Account Policy is applied to idm_all_accounts. This provides the defaults that influence all accounts in Kanidm. This policy can be modified the same as any other group's policy.

Enforced Attributes

Auth Expiry

The maximum length in seconds that an authentication session may exist for.

Password Minimum Length

The minimum length for passwords (if they are allowed).

Privilege Expiry

The maximum length in seconds that privileges will exist after reauthentication for to a read/write session.

Webauthn Attestation

The list of certificate authorities and device aaguids that must be used by members of this policy. This allows limiting devices to specific models.

To generate this list you should use fido-mds-tool.

Policy Resolution

When an account is affected by multiple policies, the strictest component from each policy is applied. This can mean that two policies interact and make their combination stricter than their parts.

Example Resolution

If we had two policies where the first defined:

auth-session: 86400
password-minimum-length: 10
privilege-expiry: 600
webauthn-attestation-ca-list: [ "yubikey 5ci", "yubikey 5fips" ]

And the second

auth-session: 3600
password-minimum-length: 15
privilege-expiry: 3600
webauthn-attestation-ca-list: [ "yubikey 5fips", "feitian epass" ]

As the value of auth-session from the second is smaller we would take that. We would take the smallest value of privilege-expiry from the first. We would take the largest value of password-minimum-length. From the intersection of the webauthn attestation CA lists we would take only the elements that are in both. This leaves:

auth-session: 3600
password-minimum-length: 15
privilege-expiry: 600
webauthn-attestation-ca-list: [ "yubikey 5fips" ]

Enabling Account Policy

Account Policy is enabled on a group with the command:

kanidm group account-policy enable <group name>
kanidm group account-policy enable my_admin_group

Setting Maximum Session Time

The auth-session value influences the maximum time in seconds that an authenticated session can exist. After this time, the user must reauthenticate.

This value provides a difficult balance - forcing frequent re-authentications can frustrate and annoy users. However extremely long sessions allow a stolen or disclosed session token/device to read data for an extended period. Due to Kanidm's read/write separation this mitigates the risk of disclosed sessions as they can only read data, not write it.

To set the maximum authentication session time

kanidm group account-policy auth-expiry <group name> <seconds>
kanidm group account-policy auth-expiry my_admin_group 86400

Setting Minimum Password Length

The password-minimum-length value defines the character length of passwords that are acceptable. There are no other tunables for passwords in account policy. Other settings such as complexity, symbols, numbers and so on, have been proven to not matter in any real world attacks.

To set this value:

kanidm group account-policy password-minimum-length <group name> <length>
kanidm group account-policy password-minimum-length my_admin_group 12

Setting Maximum Privilege Time

The privilege-expiry time defines how long a session retains its write privileges after a reauthentication. After this time, the session returns to read-only mode.

To set the maximum privilege time

kanidm group account-policy privilege-expiry <group name> <seconds>
kanidm group account-policy privilege-expiry my_admin_group 900

Setting Webauthn Attestation CA Lists

The list should be generated with fido-mds-tool. This will emit JSON that can be directly used with Kanidm.

kanidm group account-policy webauthn-attestation-ca-list <group name> <attestation ca list json>
kanidm group account-policy webauthn-attestation-ca-list idm_all_persons '{"cas":{"D6E4b4Drh .... }'

NOTE: fido-mds-tool is available in the kanidm:tools container.

Global Settings

There are a small number of account policy settings that are set globally rather than on a per group basis.

Denied Names

Users of Kanidm can change their name at any time. However, there are some cases where you may wish to deny some name values from being usable. This can be due to conflicting system account names or to exclude insulting or other abusive terms.

To achieve this you can set names to be in the denied-name list:

kanidm system denied-names append <name> [<name> ...]

You can display the currently denied names with:

kanidm system denied-names show

To allow a name to be used again it can be removed from the list:

kanidm system denied-names remove <name> [<name> ...]

Password Quality

Kanidm enforces that all passwords are checked by the library "zxcvbn". This has a large number of checks for password quality. It also provides constructive feedback to users on how to improve their passwords if they are rejected.

Some things that zxcvbn looks for is use of the account name or email in the password, common passwords, low entropy passwords, dates, reverse words and more.

This library can not be disabled - all passwords in Kanidm must pass this check.

Password Badlisting

This is the process of configuring a list of passwords to exclude from being able to be used. This is especially useful if a specific business has been notified of compromised accounts, allowing you to maintain a list of customised excluded passwords.

The other value to this feature is being able to badlist common passwords that zxcvbn does not detect, or from other large scale password compromises.

By default we ship with a preconfigured badlist that is updated over time as new password breach lists are made available.

The password badlist by default is append only, meaning it can only grow, but will never remove passwords previously considered breached.

You can display the current badlist with:

kanidm system pw-badlist show

You can update your own badlist with:

kanidm system pw-badlist upload "path/to/badlist" [...]

Multiple bad lists can be listed and uploaded at once. These are preprocessed to identify and remove passwords that zxcvbn and our password rules would already have eliminated. That helps to make the bad list more efficient to operate over at run time.

Password Rotation

Kanidm will never support this "anti-feature". Password rotation encourages poor password hygiene and is not shown to prevent any attacks - rather it significantly weakens password security.